ACMOC Bulletin Board http://www.acmoc.org/bb/ en Wed, 19 Jun 2013 09:49:55 GMT vBulletin 60 http://www.acmoc.org/bb/images/misc/rss.png ACMOC Bulletin Board http://www.acmoc.org/bb/ Need weight on 955H Loader http://www.acmoc.org/bb/showthread.php?18723-Need-weight-on-955H-Loader&goto=newpost Wed, 19 Jun 2013 05:46:45 GMT Hi, bought this 955h with locked motor, picked it up the other day but had alot of trouble loading from the rear of hyster because I was curious to... Hi, bought this 955h with locked motor, picked it up the other day but had alot of trouble loading from the rear of hyster because I was curious to see how the new winch installation went. We put a 30,000 lb tulsa hydraulic on it, this 955 is much heavier than normal, six smaller counter weights of 3 to 5 hundred lbs each and one big one that is 30 inchs by 49 inchs and is 4 inchs thick, has heavy rops and side dump bucket. I thought base weight on 955 was around 34,000. This thing feels more like 40,000, how far off am I ? Thanks for any guesstimates. will add more close up photos shortly
Attached Images
]]> DISCUSSION D4D83J http://www.acmoc.org/bb/showthread.php?18723-Need-weight-on-955H-Loader Ebay 30 tractor http://www.acmoc.org/bb/showthread.php?18722-Ebay-30-tractor&goto=newpost Tue, 18 Jun 2013 22:30:17 GMT 30 http://www.ebay.com/itm/caterpillar-...item3383138a09 ]]> FOR SALE/WANTED chriscokid http://www.acmoc.org/bb/showthread.php?18722-Ebay-30-tractor 14A Pony Carburetor http://www.acmoc.org/bb/showthread.php?18721-14A-Pony-Carburetor&goto=newpost Tue, 18 Jun 2013 22:20:52 GMT I am in need of a carburetor for the pony engine for serial number 14A 1160. I really don't need the whole carb but the choke shaft as the arm is broken off. I will buy either a whole carb or the part needed. Thanks ]]> FOR SALE/WANTED 657bruce http://www.acmoc.org/bb/showthread.php?18721-14A-Pony-Carburetor D-7 3T Upper Bellhousing Needed. http://www.acmoc.org/bb/showthread.php?18720-D-7-3T-Upper-Bellhousing-Needed&goto=newpost Tue, 18 Jun 2013 22:05:22 GMT This is casting number 2F3316 and fits serial number 3T1179 or a cross over that is the same. This is casting number 2F3316 and fits serial number 3T1179 or a cross over that is the same. ]]> FOR SALE/WANTED 657bruce http://www.acmoc.org/bb/showthread.php?18720-D-7-3T-Upper-Bellhousing-Needed Which nozzles to use in CAT 922A D320T engine? http://www.acmoc.org/bb/showthread.php?18719-Which-nozzles-to-use-in-CAT-922A-D320T-engine&goto=newpost Tue, 18 Jun 2013 14:53:08 GMT Hello you all, I am about to replace the turbo non my CAT 922A S/N 59A1987 as it burns oil and replace the ferrules and head gasket as it... Hello you all,
I am about to replace the turbo non my CAT 922A S/N 59A1987 as it burns oil and replace the ferrules and head gasket as it occasionally leaks some water out of the head gasket, especially when it has run only short not reaching the operating temperature.
As it smokes I might also renew the injectionnozzles.
My book says Service group 5M2788 which has been changed into 3S6638 which contains a 2S4442 nozzle.
If i read other posts on this subject I find 2S4442 nozzles to be correct for non turboed engines where mine does have a turbo.
So I am confused now although I tend to go by the book and use the 3S6638 service group.
Who can bring some clarity here?
All reactions wellcome.

Thanks
Nico ]]> DISCUSSION Nico Ensink http://www.acmoc.org/bb/showthread.php?18719-Which-nozzles-to-use-in-CAT-922A-D320T-engine Interesting ramble through time. http://www.acmoc.org/bb/showthread.php?18718-Interesting-ramble-through-time&goto=newpost Tue, 18 Jun 2013 13:24:20 GMT Hi, Folks. Some of you might like to take a ramble back through time on this site: ... Hi, Folks.
Some of you might like to take a ramble back through time on this site:

http://www.flickr.com/photos/1326814...5710/lightbox/

LOTSA interesting stuff there.

Just my 0.02. ]]> DISCUSSION Deas Plant. http://www.acmoc.org/bb/showthread.php?18718-Interesting-ramble-through-time D8H turbo http://www.acmoc.org/bb/showthread.php?18717-D8H-turbo&goto=newpost Tue, 18 Jun 2013 04:05:29 GMT Howdy Does anyone what the correct turbo for a D8H serial # 46A10316 would be ? Currently has 3s8273 which i am told is the wrong one? Any... Howdy

Does anyone what the correct turbo for a D8H serial # 46A10316 would be ?

Currently has 3s8273 which i am told is the wrong one?

Any help appreciated
Thanks ]]> DISCUSSION ashcat http://www.acmoc.org/bb/showthread.php?18717-D8H-turbo Need information. AGAIN! http://www.acmoc.org/bb/showthread.php?18716-Need-information-AGAIN!&goto=newpost Mon, 17 Jun 2013 20:06:10 GMT I would like to know the hyd pressure of a LaPlante-Choate pump. Model 9. I have searched past posts and have not come upon any usefull info. I... I would like to know the hyd pressure of a LaPlante-Choate pump. Model 9. I have searched past posts and have not come upon any usefull info. I guess I could put a guage on a line, but if someone knows it would save me the trouble. Thanks. ]]> DISCUSSION jbernd56 http://www.acmoc.org/bb/showthread.php?18716-Need-information-AGAIN! Museums in the Netherlands.... http://www.acmoc.org/bb/showthread.php?18715-Museums-in-the-Netherlands&goto=newpost Mon, 17 Jun 2013 14:36:25 GMT I am planning a trip to the Netherlands (Holland) and wondered if anyone could recommend agricultural / tractor / industrial museums and collections... I am planning a trip to the Netherlands (Holland) and wondered if anyone could recommend agricultural / tractor / industrial museums and collections that would be good to visit. ]]> DISCUSSION gauntjoh http://www.acmoc.org/bb/showthread.php?18715-Museums-in-the-Netherlands Wanted D7-3T19888 Pony Motor Exhaust Manifold http://www.acmoc.org/bb/showthread.php?18714-Wanted-D7-3T19888-Pony-Motor-Exhaust-Manifold&goto=newpost Mon, 17 Jun 2013 14:29:01 GMT We are needing an exhaust manifold for our Cat D7 3T19888 pony motor. Dad took the pony motor off to get it rebuilt, laid the exhaust manifold down... We are needing an exhaust manifold for our Cat D7 3T19888 pony motor. Dad took the pony motor off to get it rebuilt, laid the exhaust manifold down by the barn and it got stolen along with some other stuff that was replaceable. Any ideas as where I should look to find one of these? Any help is appreciated. ]]> FOR SALE/WANTED chilliewillie57 http://www.acmoc.org/bb/showthread.php?18714-Wanted-D7-3T19888-Pony-Motor-Exhaust-Manifold CAT c-frame on Allis HD-11? http://www.acmoc.org/bb/showthread.php?18713-CAT-c-frame-on-Allis-HD-11&goto=newpost Sun, 16 Jun 2013 17:52:18 GMT Just bought my first dozer - Allis Chalmers HD-11. I know this isn't the Allis forum, but was looking it over today and the blade has a Allis-Chalmers tag on it (Model 11-GD, Serial 2232), but the c-frame has a part number of 5F746 or perhaps 6F746. To me that looks like a CAT number. What do the experts think?

Andrew ]]> DISCUSSION Andrew_D http://www.acmoc.org/bb/showthread.php?18713-CAT-c-frame-on-Allis-HD-11 44 hyd pump seal replacement http://www.acmoc.org/bb/showthread.php?18712-44-hyd-pump-seal-replacement&goto=newpost Sun, 16 Jun 2013 15:51:45 GMT I posted this earlier on the For Sale site, did not realize I was there when I posted it! Trying to replace the seals around the drive shaft on my... I posted this earlier on the For Sale site, did not realize I was there when I posted it!

Trying to replace the seals around the drive shaft on my #44 hyd pump ser #6W12536. I have the unit off and have also pulled the pump from the unit. I have a copy of the page from a parts book showing the parts detail so at least I can see what they look like

My question is can the "Retainer" part #4F3964, which appears to hold the seal, be removed by just taking out the 4 cap screws? Or do I have to dismantle the whole pump?

I have tapped on it with a chisel to try and get it free and then I tapped a little harder. It does not seem to have budged at all. The pump seems fine so I would rather not take it all to pieces if I do not have to.

Thanks for any advice, randy ]]> DISCUSSION randy merrick http://www.acmoc.org/bb/showthread.php?18712-44-hyd-pump-seal-replacement #44 Hyd Pump input shaft seal replacement? http://www.acmoc.org/bb/showthread.php?18711-44-Hyd-Pump-input-shaft-seal-replacement&goto=newpost Sun, 16 Jun 2013 14:40:48 GMT Trying to replace the seals around the drive shaft on my #44 hyd pump ser #6W12536. I have the unit off and have also pulled the pump from the unit.... Trying to replace the seals around the drive shaft on my #44 hyd pump ser #6W12536. I have the unit off and have also pulled the pump from the unit. I have a copy of the page from a parts book showing the parts detail so at least I can see what they look like

My question is can the "Retainer" part #4F3964, which appears to hold the seal, be removed by just taking out the 4 cap screws? Or do I have to dismantle the whole pump?

I have tapped on it with a chisel to try and get it free and then I tapped a little harder. It does not seem to have budged at all. The pump seems fine so I would rather not take it all to pieces if I do not have to.

Thanks for any advice, randy ]]> FOR SALE/WANTED randy merrick http://www.acmoc.org/bb/showthread.php?18711-44-Hyd-Pump-input-shaft-seal-replacement Cat D12 on transport http://www.acmoc.org/bb/showthread.php?18710-Cat-D12-on-transport&goto=newpost Sun, 16 Jun 2013 10:43:27 GMT A Caterpillar D2 A Caterpillar D2
Attached Images
]]> DISCUSSION QuAD http://www.acmoc.org/bb/showthread.php?18710-Cat-D12-on-transport D7 47a http://www.acmoc.org/bb/showthread.php?18709-D7-47a&goto=newpost Sun, 16 Jun 2013 02:45:26 GMT Anyone know where to find a complete gasket kit with all gaskets and seals etc. for rebuilding a D339T? Cat tells me the kits are no longer... Anyone know where to find a complete gasket kit with all gaskets and seals etc. for rebuilding a D339T?

Cat tells me the kits are no longer available but that they can still sell gaskets individually. This seems way too hard.. ]]> DISCUSSION cab http://www.acmoc.org/bb/showthread.php?18709-D7-47a