Activity Stream

14 B GRADER, asking price 7000.00 it is a worn out piece of shit, oh boy it runs and has a turbo, big fucking deal, lets say 15 ton if that, scrap...

Someone made some a year or 2 back and was trying to sell a extra set-- If they don't chime in I used grade 8 threaded (plated)rod and welded a nut...

Hi Fred, yes mine is a D2 but the approach should work equally well for your D6 starter. I made a tin "sump" for the idler gear and put some oil in...

When I had my F model the hyd pump went out.I couldn't find a pump with the control valve in it. I went to the local hyd shop,got a belt driven pump...

Hello TW , Do you wanted to sell this ?? Hollandcat

Yup, you got it, more fuel burning takes more air and increases the exhaust flow.

I have what I am told is a NOS canopy . No Canvas or the strips that hold the canvas on. Terry

I still have about 35 numbers to go, but will take a break. I have a couple of Starters/Generators/motors that I want to photo and post them here for...

I have 4 cams 7b5758 8 links 7b5647 8 pins 7b5693 and these parts number came from my manual D4-2T serie 8245 to 9999

7B2174 seal; lip type seal, 336 entries, numerous applications 5S6622 seal; lip type seal, 377 entries, numerous applications DR-1481 is not a Cat...

Thanks again Brian, I see those "Links" and "Pins" are used in the clutches of my old RD4, D4 7J and D4 2T, using those older P/N's was not getting...

So if they are the same how does one deliver more air? This post stumped me old magnet! Does the increased fuel delivery spin it up faster or?? ...

Hi Billy, I have Wilson's contact details, I'll PM them to Luke, I was thinking Mark's Carburetor Service in the USA might have them too, but...

You could just buy a D2... Greg

5/4 red oak frames with marine grade plywood cut into small strips for the top. The top is then covered with canvas which is held into place with...

Very good, thanks. Just the thought of getting it off and on the D6 makes my back ache. I thought you only were goofing around with a D4. fred

thanks Deas Plant!!

The 8M2679 turbo produces 32 +/-3 in. Hg boost @ full load and speed. The early 4S9706 turbo (160 hp) produces 25 +/- 3 in. Hg. The same 4S9706 is...

Yes i may well be interested. Please, if you can, give me serial number of dismantled 47a and part number of turbo. Also condition and price if you...

If you searched using the S and B part numbers all searches show nothing. Searching machinery trader with the 7B numbers turns up a few places. You...

I made a canopy a few years ago using an original for a pattern. I am almost sure it was white oak. My memory says that was the consensus here on the...

I bought one of those jets from Wilson's carbs in Melbourne. I can dig up their contact info if you want.

10k is about right. I haven't put the seals in the right side yet, so I may need bearings there. I also replaced all the wear bars on the track...

I dismantled a d7-47a machine and am still have the turbo if I can help

nice job- good for 15 years or so, Those costs equate with what the Cat sages told me, that is, if the undercarriage requires new chains, rollers,...

Hi, Scocchius. Here is a link to the site for these little jiggers: http://groups.yahoo.com/group/tracklayinggardentractors/ ...

Hi there, Do you have the radiator cap? I just picked up a 22 and the lower half of the radiator is cracked also. I'm missing the radiator cap...

Hi Brian, Many thanks for that info, I really appreciate your help, that's really weird because I contacted Florin about those parts a few months ago...

JP, the water heater igniter wire was faulty. After it ignites the flame it continues to read the heat to keep the gas flowing. The tech put a new...