- Posts: 2473
- Thank you received: 2
ACMOC Membership Benefits
- FREE quarterly magazine filled with content about antique Caterpillar machines
- FREE classified listings
- ACMOC store discounts and specials
- Full Bulletin Board Access
- Marketplace (For Sale/Wanted)
- Technical Library
- Post attachments
$44 /year ELECTRONIC
$60 /year USA
$77 /year International
D2 drawbar part made
10 years 10 months ago #88271
by STEPHEN
D2 drawbar part made "shoe" was created by STEPHEN
Years ago I wrapped a chain around my drawbar to pull something, the chain slipped and ripped off part of the wear plate that fits between the bar and quadrant. I finally made a new one for my machine, and a few more for you guys. I have seen a lot of D2's with the plate missing, or worn very thin. I looked in my parts book but couldn't see a drawing of it, there is a arrow to the area with the name "shoe" 8B8728
$15.00 + postage. ---PLEASE SEND EMAIL, AS THE PM BOX STORAGE IS VERY SMALL, THANKS----
$15.00 + postage. ---PLEASE SEND EMAIL, AS THE PM BOX STORAGE IS VERY SMALL, THANKS----
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88273
by bcwayne
Replied by bcwayne on topic D2 drawbar part made
They look great... I'll take four. PM sent
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88275
by STEPHEN
Replied by STEPHEN on topic D2 drawbar part made
Thanks BC, I sent you an e-mailThey look great... I'll take four. PM sent
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88283
by Paso Bob
D-4 7U-43159 with 4S dozer and Cat 40 scraper, D-7 3T-1179 with Cat 7S hydraulic dozer, D-7 17A 13,944, D-8 14A-1160 with Cat 8S cable dozer, Cat 12-99E-4433 Grader. All runners and users.
Replied by Paso Bob on topic D2 drawbar part made
Good looking work. It will be fun to get the drawbar off to install them after 70 years of the bolts being rusted in place. It will take a lot of heat and a long cheater on the 3/4 drive set!
D-4 7U-43159 with 4S dozer and Cat 40 scraper, D-7 3T-1179 with Cat 7S hydraulic dozer, D-7 17A 13,944, D-8 14A-1160 with Cat 8S cable dozer, Cat 12-99E-4433 Grader. All runners and users.
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88317
by STEPHEN
Replied by STEPHEN on topic D2 drawbar part made
Wayne, Neil, & Bob, I sent the parts. Please post a few pics of your installation. Thanks, Stephen
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88321
by neil
Cheers,
Neil
Pittsford, NY
Replied by neil on topic D2 drawbar part made
Excellent thanks Stephen. So long as the pic doesn't show the sorry state of the rest of the tractor, happy to post pics ; )
Pulled apart the fuel transfer pump tonight and cleaned all the gunk out of it, shinied it up on the wire wheel, and put it back together. The boss in the kitchen says I can work on it on Sunday so I'll be pulling the clutch and pinion
Cheers,
Neil
Pulled apart the fuel transfer pump tonight and cleaned all the gunk out of it, shinied it up on the wire wheel, and put it back together. The boss in the kitchen says I can work on it on Sunday so I'll be pulling the clutch and pinion
Cheers,
Neil
Cheers,
Neil
Pittsford, NY
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88428
by STEPHEN
Replied by STEPHEN on topic D2 drawbar part made
Joe and Gary, I mailed the parts this morning, thank-you
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88430
by 4D2Ken
Replied by 4D2Ken on topic D2 drawbar part made
Pardon my ignorance, but I've never seen one of those before. All I've ever seen is a pin that holds the drawbar to one side or the other and I've let the drawbar float between the pin and right/left end of the drawbar. This makes turning while pulling a load easier, or so I'm told. This looks like it holds the drawbar more or less solid. How does it get adjusted?
Whoops, nevermind, I see now it's a wear plate that slides and is not pinned into place. Sorry 'bout that!
Whoops, nevermind, I see now it's a wear plate that slides and is not pinned into place. Sorry 'bout that!
Please Log in or Create an account to join the conversation.
10 years 10 months ago #88431
by STEPHEN
Yes, to keep your drawbar and support from getting worn out.
Replied by STEPHEN on topic D2 drawbar part made
Pardon my ignorance, but I've never seen one of those before. All I've ever seen is a pin that holds the drawbar to one side or the other and I've let the drawbar float between the pin and right/left end of the drawbar. This makes turning while pulling a load easier, or so I'm told. This looks like it holds the drawbar more or less solid. How does it get adjusted?
Whoops, nevermind, I see now it's a wear plate that slides and is not pinned into place. Sorry 'bout that!
Yes, to keep your drawbar and support from getting worn out.
Please Log in or Create an account to join the conversation.
Time to create page: 0.172 seconds
ACMOC
Antique Caterpillar Machinery Owners Club
1115 Madison St NE # 1117
Salem, OR 97301
cat@acmoc.org
Become a Member!
"I became a member recently because the wealth of knowledge here is priceless."
- Chris R
"I also joined a year ago. had been on here a couple of times as a non-member and found the info very helpful so I got a one year subscription (not very expensive at all) to try it out. I really like all the resources on here so I just got a three year. I think its a very small price for what you can get out of this site."
- Jason N